How to Make a Backlight for a Crane

As in the night, not including indoor light, open the tap with cold water? You can try to find it at random. Or you can include memory. And you can consider this situation in advance and make the backlight for the crane.

You will need

- Plastic clutch;

- Plastic caps;

- LED color changing faucet lights;

- A small nipple;

- 20-cc syringe;

- 5 cc syringe;

- The wire;

- Batteries in the form of a tablet;

- Toggle switch;

- Impeller with a nozzle;

- Soldering iron;

- Drill with a drill;

- Knife.

BTW, you can select the LED faucet lights and the tools mentioned above at Banggood for high quality and reasonable prices.

Cut by a turbine in the middle of the plastic cap (on the outside of his hand) hole using a special circular nozzle. Drill the side of the plastic sleeve hole is designed to be installed in his switch. Cut the tip of the knife 20, a bottom of the syringe. Place a bottom housing 20 in a plastic syringe cap. The one end of the syringe, which protrudes from under the hood, and connect the nipple (Shove thin section of the pin in the syringe).

From 5-bottoms make the syringe container for batteries. Solder to the design of the container with battery. Then attach using a soldering iron to the hood blue and red LEDs. Pass the wire through the hole on the plastic sleeve. On the plastic cap on top put a plastic sleeve. By withdrawing from the coupling wire, attach a small toggle switch. Check the operation of the mechanism established by setting the switch to a different position. Screw design instead of a shower or faucet. When the hot water is turned on, it should be highlighted in red, and when the cold, it is blue.

To make a 5-bottoms syringe container for batteries, need copper foil, wire, glue gun with, the battery itself and the syringe. To begin, cut with a knife tip of the syringe and pull the wires through the body of the syringe. At the bottom of the copper foil preform place. Cover the glue nozzle of the syringe to the wire, and the second route the transactions through the piston, connecting it with the copper contacts. Place the syringe button-type battery and a container ready.

LED Spotlights Outdoor and Indoors

Today, LED spotlights are the ideal lighting solution for modern cities, streets, buildings, bridges, billboards, parking lots of storage space and adjacent areas. These light sources were an indispensable tool to create a unique image of the city, accents, show and highlight the beauty of the historic buildings, as well as the scale of buildings. LED spotlights are the modern replacement of legacy projectors with halogen and metal halide lamps. LED floodlights provide bright and directional light, with maximum energy saving, long service life, high degree of protection against mechanical damage and environmental influences and does not require additional maintenance costs.

Consider the unit LED spotlights on the example of a model from one of the well-known manufacturers of 50 watts. Modern LED spotlights (e.g. 10W LED Chip Lamp) from top manufacturers available in modern and functional packaging with bright memorable design, which distinguishes them from noname products. Spotlight housing and is usually made of a cast aluminum alloy having a high thermal conductivity, which allows heat removal from the LED module. The reflector is typically made of metal. With coated aluminum deposition in a vacuum creates an even light output with given scattering angle, providing high consumer properties of the spotlight. Silicone seals and grooves on the spotlight housing provide high protection of electronic components against moisture spotlight.

These models are designed for outdoor use. Cheap as spotlights unknown manufacturers have moisture protection at this level. Moreover, the poor quality of the assembly can be clearly seen with the naked eye. Housing of high-quality LED spotlights usually has a special anti-corrosion powder coating that provides protection against mechanical damage and environmental impact (e.g. water does not linger on the body as opposed to the usual smooth coat). The modern LED spotlights used inside the housing are located LED module made on the chip on board technology (COB). The diffuser is made of clear tempered glass.

LED spotlights do not require additional services, which allow to minimizing the costs of their operation. Swivel bracket makes it easy to install the spotlight, as well as direct the luminous flux in the desired direction. BTW, you can select the in ground flood light at Banggood. Besides, you can easily get other LED lighting accessories (e.g. 5V light bulb) there with high quality and reasonable prices.

How to Connect LED Strip

Backlight LEDs actively spreading in modern design. LED strips are used in various fields. For example, LEDs are used in the interior spaces of buildings. The shop windows are also illuminated lights from LEDs in cars are also used LED strip. Low cost, practicality and easy installation LEDs have provided widespread.

You will need

- IP65 LED Light Strip

- Power Supply

- Scissors

- Soldering iron

In the beginning, you need to decide on the venue installation LED strip and calculate the length of its future. One must remember that the LED strip can be cut through multiple intervals (for example, SMD 3528 Q60 tape can be cut every 5 cm), so you need to take this into account in the calculation.

The next step is the selection of the power supply. The power supply must strictly conform to the stated capacity of the tape. In the selection of the block is best to consult with a professional advisor, not to be mistaken.

After all, the components purchased to prepare the surface for the tape mounting. Mounting location carefully degreased. It is better if the surface is solid (in order to avoid damage to the tape PCB). If the tape be mounted on metal or other conductive surfaces, the tape must be isolated. If the tape does not need to cut, it is immediately ready for installation. LED strips have a back side of the adhesive layer. With this adhesive layer and made assembling strip. The protective coating is removed and the tape pressed against the surface. BTW, you can select the LED strips at Banggood. Besides, you can easily get other LED light (e.g. stainlesss teel wall mounted solar light) there with high quality and reasonable prices.

The final step is to connect the tape to the power supply and controller, which is produced by wires from the tape. Each wire has its own designation on the conductive path, R, G, B, and V +, and connected respectively polarity to 4 inputs on the controller R, G, B, V + .Blok power to 220V connect the two wires to terminals L + and N-. Next, connect the "+" on the power supply to the "+" on the controller, and "-" to "-", respectively. Voltage polarity must not be confused - this can lead to equipment failure and damage to the tape.

Installation of LED Ribbon on the Car

Until a few decades ago, LEDs were only used as indicator lights. But today, thanks to its characteristics, versatility and beautiful glow, LED-technology every year are gaining popularity in the field of lighting. Consumers are increasingly moving to the use of LED lamps and luminaires, as well as LED strips, which have been applied in advertising and decorative lighting, and actively used by designers all over the world.

In addition to the design goals of interior room lighting, LED strip steel (e.g. the 12V LED strip lights) is widely used in the automotive industry, to enhance the standard lighting cars. Some manufacturers of modern cars already in the basic equipment of the models set the LED backlighting in size and dashboard. However, for many motorists, who want to give your vehicle a unique look and add functionality to the standard interior lighting, boot or body, this is not enough. So they resorted to self-tuning of the car, using the LED strip, by which additional lighting can be set in the most unusual places, even where it did not exist before.

For successful device further highlight the car must follow these steps:

1. Determine the place of installation of LEDs;

2. Cut the tape only in the right place;

3. Qualitatively fulfill its connection to the onboard network.

There are two ways to connect the LED strip: no interference in the electric car circuit and with a hole in it. When laying the tape should be selected segments of the desired value, which are cut to the ground and fold sequentially connected together by soldering the wires through the connectors. It is necessary to strictly observe the polarity, but in the case of improper connection LEDs will not go down. If the light does not work, you will need to check the correctness of the connection. Places soldering, to prevent ingress of water, treated with silicone. Connect LED ribbon through the controller (in the passenger car - 12 V) to the power supply using the adapter into the vehicle's cigarette lighter. To this end, a standard telephone charge soldered wires from the LED strip, with one wire is fixed to a fuse, and the second - bypassing the regulator to rule with an iron lug. And you can use the RGB LED connector.

To implement the second method of connecting the tape with a hole in the car's electrical circuit, only need two additional wires. In order not to reverse the polarity, it is best to use the red and black wires. Red is soldered to the "plus" ribbons, black - a "minus". And then solder joints should be treated with sealant. Black wire is held under the skin to the negative terminal of the battery and the red through the switch - to the positive. The switch is installed inside the vehicle so that it to be easy to get.

Night Lights with a Magic Illusion of 3D

With the development of modern technologies, all, even the most ordinary things, are changing rapidly. Objects take many different forms, often combine incongruous features. Innovations were made in lighting. Today, I am pleased to present you a novelty, an amazing lamp with 3D effect.

These lights look like the real thing about the future of film. It seems that volumetric luminous figure hovers in the air. This unusual 3D effect is achieved by a special form of special LED strands. Diffuser is placed on the stand, which, by the way, is universal, so you can easily change the ceiling. You can change the color of light by pressing the touch of a button.

3D Illusion Color Changing Clown & Batman Double-sided LED Desk Night Light Lamp

This 3D illusion lamp comes with 8 color modes, red, green, blue, yellow, cyan, pink, and white, all color flashing in turn. With the USB cable, you can connect it to your home power socket or computer USB port. It can be put in bedroom, child room, living room, bar, shop, cafe, restaurant, etc. as decorative light.

Pay attention not to touching the acrylic plate surface with your fingers to avoid finger print marks on the plate which may affect the 3D illusion. And you can use the soft cloth to clean the acrylic plate if there is mark on the surface.

3D Illuminated Illusion Color Changing Gun LED Desk Night Light Lamp Xmas Gift

Made of high quality Acrylic material, the 3D illuminated gun lamp is environmental, non-toxic, and quite durable. This piece creates an optical illusion, as it appears as a 3D light bulb, but is actually completely flat. You can get seven colors to choose, and use it to perfectly decorate your room, making the room more beautiful and attractive. This creative decor light can be applied to party lighting and holiday lighting, or as a night light and bedside light.

And you can get any of the 3D Night Lights mentioned above at Banggood for shining miracle to decorate your home and office.

How Do I Install the LED Strip for Headlights?

Once entered into force a law on mandatory inclusion of illumination lights in any weather, many car owners have begun to look for ways to at all costs not to include them. Because we all know, in this case, all lights will break down faster. Most nimble found out - LED strip for headlights with their own hands, the issue we have decided to devote special attention and tell the features of this connection, and why such a light is allowed at the legislative level.

Many believe that this extra light and creates only "Pont" We fundamentally disagree with this opinion. After all, we consider that the installation of LED strip lights battery powered - it is a useful factor that makes the car better and allows you to not include running lights of the city.

Modern brands set a default backlight, however, it is found only in expensive models. Everyone will be able to set it up it on your car, too much difficulty it is not enough to follow certain rules in order not to have problems with the traffic police authorities.

Any feature LED strip with battery for the car is that the conventional tape shines at an angle of 120 degrees - such light unacceptable. It is necessary to create a viewing angle of 30 degrees, and then it will perform the DRL function, creating visibility to at least 300 meters. The optimal degree of luminescence is created by reflectors and lenses. I would like to reassure the right, if you can buy LED strip for cars, then these lenses and reflectors are installed by default.

How to Choose a Power Supply for LED Strip

Many people know that connect LED strips directly into the outlet should not be - it will burn immediately. To do this, use a power supply for LED strip, and choose how to calculate the power and ribbon, we'll tell you in this article.

In total there are basically two: the power supply for LED 12W tape and 24 watts. We recommend using 12W, because they cost much less at the same time carry out such functionality. Power 12W is considered optimal, they can be easily found at any market. To install at home is better not find the device. If you connect a large tape, then you will come in handy at 24 watts, as a rule, to illuminate a large area of a stretch ceiling it will fit just right. If you want to do without a block, then think about the LED ribbon RGB on line 220. BTW, you can select the power supply for LED Strip at Banggood. Besides, you can easily get other lighting and lighting accessories (e.g. LED strip adapter) there with high quality and reasonable prices.

Let's try to make the calculation on the basis of one meter LED strip SMD 5050. The table shows the value of 7.2 watts. Next, we determine the length of our tape, take, for example, the tape 10 meters. Perform simple multiplication: 10 meters multiply by 7 watts. It turns out 72 watts - a power which should have a block.  They can be found in any store, they differ only in the installation process. For example, one can only be installed in a dry room, and the other can be installed even in the bathroom. They are considered the most popular although many people do not even use them to full functionality. Maximum power of this unit is 75 watts. This capacity is enough for an average LED strip. This unit can be used for lighting LED ceiling ribbon.

Outdoor 12V 20A power supply for LED strip has a very large size, so it cannot be set as the illumination of walls, ceilings, because it cannot hide anywhere. It is used to illuminate large areas and only in the room, for example, it can be hidden in ordinary wardrobe. Keep from moisture and mechanical impact, but it has a low cost. 

How to Connect the Motion Sensor Lighting

Each person more than once noticed motion sensors, which include light. Such an arrangement can be called great, it is suitable for installation: at the entrance, on the street, near a private house, on the fence, etc. In this article we will answer the burning question, how to connect a solar motion sensor light to illuminate on our own hands, just want to point out the complex in such a setting there is nothing one can do it.

Any motion sensor for switching of lighting has a fairly simple principle of work. There are three species that respond to a particular signal.

1. Responsive to sound.
2. Vibrational. In this case, it closes the circuit when they see near objects.
3. Infrared responsive to heat.

We now consider the more important question, and figure out how to connect the motion detector. Now there are several combinations, each of them has its own characteristics.

The first circuit connecting the motion sensor is the simplest, but at the same time it cannot be considered optimal for installation in home or apartment. The light will turn on only when the sensor detects motion. The second scheme is considered to be optimal. It is possible to switch the circuit breaker to normal. Everything can be turned on or off manually if desired. The third circuit is necessary in the case where the nominal transmitter power ranges from 500 to 1000 watts. According to this scheme are connected solar powered motion lights, it is desirable to add to the circuit magnetic contactor. Last connection diagram of the motion sensor is used when you need to install it in large rooms or at their summer cottage. It can also be applied to the winding corridor, the scheme is considered quite complicated. It is usually used only by professionals. BTW, you can select the solar-powered motion sensor security light at Banggood. Besides, you can easily get other lighting and lighting accessories (e.g. warm white LED flood light) there with high quality and reasonable prices.